summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorLines
2020-03-18Arduino: Add ADC driverDaniel Friesel-0/+105
2020-03-18add mpu9250 datalogger variant with button handler and adcDaniel Friesel-0/+282
2020-03-11Add S5851A temperature sensor driverDaniel Friesel-0/+55
2020-03-08mpu9250_motionlog: monitor magnetismDaniel Friesel-1/+18
2020-03-08mpu9250: getRawMagnet: pass request success to userlandDaniel Friesel-3/+4
2020-03-08mpu9250_motionlog: measure VCCDaniel Friesel-0/+20
2020-03-08HDC1080: Add heater toggleDaniel Friesel-1/+14
2020-03-06ws2812b_uart: monitor VCCDaniel Friesel-0/+11
2020-03-02i2cdetect: fix mpu9250 usageDaniel Friesel-3/+3
2020-02-17ledblink: remove timer_cycles / timer_s dependencyDaniel Friesel-9/+2
2020-02-14luxlog: increase buffer size, decrease heartbeat intervalDaniel Friesel-5/+4
2020-02-12msp430 makefile: show ROM/RAM usageDaniel Friesel-0/+4
2020-01-08Add basic MAX44009 energy modelDaniel Friesel-0/+22
2020-01-08luxlog: red led while transmitting dataDaniel Friesel-0/+2
2020-01-08Add MS3430FR5994LP GPIO driverDaniel Friesel-0/+39
2020-01-08Finish simple MSP430FR5969LP GPIO driverDaniel Friesel-9/+35
2020-01-07commentDaniel Friesel-1/+1
2019-12-20add untested Arduino Nano SPI driverDaniel Friesel-2/+73
2019-12-20Makefile: Add nrf24l01 pins for arduinoDaniel Friesel-3/+13
2019-12-20nrf24l01test: set RX/TX mode via make flagDaniel Friesel-9/+13
2019-12-19Add MSP430FR5994 CPU model (datasheet values)Daniel Friesel-0/+79
2019-12-19nrf24: Add setDataRate methodDaniel Friesel-0/+8
2019-12-19add luxlog appDaniel Friesel-0/+68
2019-12-18BME: Add setStandbyTimeDaniel Friesel-2/+10
2019-12-18Add MSP430FR5969 CPU modelDaniel Friesel-0/+79
2019-12-18msp430fR5969: Add sleep_ms functionDaniel Friesel-0/+49
2019-12-12oopsDaniel Friesel-2/+2
2019-12-12mpu9250: Fix setGyroEnable/setAccelEnable. derp....Daniel Friesel-6/+6
2019-12-12mpu9250: Add nineAxis functionDaniel Friesel-0/+17
2019-12-12MSP430FR5994: switch back to 16MHz for nowDaniel Friesel-1/+1
2019-12-12bme680_util: add sleep_ms wrapperDaniel Friesel-0/+6
2019-12-12mpu9250: lowPowerAccelOnly may be called from LP_ACCEL to change update rateDaniel Friesel-1/+1
2019-12-01mpu2950_motionlog: disable unused magnetometer + gyroscope to save powerDaniel Friesel-14/+1
2019-11-28MPU9250: Add AEMR DFA driver functions and modelDaniel Friesel-1/+107
2019-11-25msp430fr5994lp: Use TI msp430-gcc 5.1.2.0Daniel Friesel-11/+10
2019-11-18ptalog barcode generation: decrease module size, increase quiet zoneDaniel Friesel-6/+6
2019-11-15ptalog: note that the current code may violate the Code128 quiet zoneDaniel Friesel-0/+3
2019-11-14ptalog: decrease delay border around barcode outputDaniel Friesel-2/+2
2019-11-13ptalog: Support barcode synchronizationDaniel Friesel-2/+17
2019-11-10blinkencat3: turn off LEDs when chargingDaniel Friesel-13/+38
2019-11-05PTALog: Add PTALOG_GPIO_BEFORE (toggle GPIO before instead of during transition)Daniel Friesel-12/+25
2019-11-05Makefiles: Fix arch_drivers and drivers overides/additionsDaniel Friesel-5/+5
+= does not work for variables specified on the commandline unless the 'override' keyword is used
2019-11-04msp430fr5994lp sleep_ms: handle ms == 0Daniel Friesel-0/+3
2019-11-04esp8266: make serial port configurableDaniel Friesel-2/+2
2019-11-04update energybench. showcase for MSP430 EnergyTrace inaccuraciasDaniel Friesel-68/+39
reported current is inaccurate (>8% energy deviation). Also, EnergyTrace++ significantly increases sleep/wakeup times and thus affects the sytem's timing.
2019-11-02mpu9250 motionlog: fix min/max calculation, decrease update rateDaniel Friesel-6/+6
2019-11-01MPU9250 motionlog: initialize values, slightly lower sample rateDaniel Friesel-4/+9
2019-11-01arduino nano: Do not declare delay_* as inlineDaniel Friesel-2/+2
2019-11-01MPU9250: Add SparkFun constants and non-raw readout of Accel and GyroDaniel Friesel-17/+450
2019-11-01ws2812b_uart: support setting arbitrary colorsDaniel Friesel-2/+32
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-29 11:47:14 +0000