initial commit

1 files changed, 254 insertions, 0 deletions

diff --git a/firmware/usbconfig.h b/firmware/usbconfig.h
new file mode 100644
index 0000000..beaec6a
--- /dev/null
+++ b/firmware/usbconfig.h
@@ -0,0 +1,254 @@
+/* Name: usbconfig.h
+ * Project: AVR USB driver
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
+ * This Revision: $Id: usbconfig.h 43 2005-04-10 21:04:36Z cs $
+ */
+
+#ifndef __usbconfig_h_included__
+#define __usbconfig_h_included__
+
+/*
+General Description:
+This file contains parts of the USB driver which can be configured and can or
+must be adapted to your hardware.
+
+Please note that the usbdrv contains a usbconfig-prototype.h file now. We
+recommend that you use that file as a template because it will always list
+the newest features and options.
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
+
+#define USB_CFG_IOPORTNAME      D
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT      3
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT       2
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0!
+ */
+/* #define USB_CFG_CLOCK_KHZ       (F_CPU/1000) */
+/* Clock rate of the AVR in MHz. Legal values are 12000, 16000 or 16500.
+ * The 16.5 MHz version of the code requires no crystal, it tolerates +/- 1%
+ * deviation from the nominal frequency. All other rates require a precision
+ * of 2000 ppm and thus a crystal!
+ * Default if not specified: 12 MHz
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME   D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT          4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT    0
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint 1.
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3   0
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 1 and an interrupt-in
+ * endpoint 3. You must also enable endpoint 1 above.
+ */
+#define USB_CFG_IMPLEMENT_HALT          0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_INTR_POLL_INTERVAL      10
+/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+ * interval. The value is in milliseconds and must not be less than 10 ms for
+ * low speed devices.
+ */
+#define USB_CFG_IS_SELF_POWERED         0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+#define USB_CFG_MAX_BUS_POWER           100
+/* Set this variable to the maximum USB bus power consumption of your device.
+ * The value is in milliamperes. [It will be divided by two since USB
+ * communicates power requirements in units of 2 mA.]
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE      0
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ       0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoint 1.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to endpoint 1.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL        0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+/* #define USB_RX_USER_HOOK(data, len)     if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+#define USB_COUNT_SOF                   0
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define  USB_CFG_VENDOR_ID  0xc0, 0x16  /* 5824 in dec, stands for VOTI */
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you use obdev's free shared
+ * VID/PID pair. Be sure to read USBID-License.txt for rules!
+ */
+#define USB_CFG_DEVICE_ID   0xdc, 0x05  /* 1500 in dec, obdev's free PID */
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you use obdev's free shared VID/PID pair. Be sure to read the rules in
+ * USBID-License.txt!
+ */
+#define USB_CFG_DEVICE_VERSION  0x00, 0x01
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME     'w', 'w', 'w', '.', 'o', 'b', 'd', 'e', 'v', '.', 'a', 't'
+#define USB_CFG_VENDOR_NAME_LEN 12
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USBID-License.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME     'P', 'o', 'w', 'e', 'r', 'S', 'w', 'i', 't', 'c', 'h'
+#define USB_CFG_DEVICE_NAME_LEN 11
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USBID-License.txt before you assign a name.
+ */
+/*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
+/*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS    0xff
+#define USB_CFG_DEVICE_SUBCLASS 0
+/* See USB specification if you want to conform to an existing device class.
+ */
+#define USB_CFG_INTERFACE_CLASS     0
+#define USB_CFG_INTERFACE_SUBCLASS  0
+#define USB_CFG_INTERFACE_PROTOCOL  0
+/* See USB specification if you want to conform to an existing device class or
+ * protocol.
+ */
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0   /* total length of report descriptor */
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ *     at runtime via usbFunctionDescriptor().
+ *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ *     in static memory is in RAM, not in flash memory.
+ *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ *     the driver must know the descriptor's length. The descriptor itself is
+ *     found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ *   char usbDescriptorDevice[];
+ *   char usbDescriptorConfiguration[];
+ *   char usbDescriptorHidReport[];
+ *   char usbDescriptorString0[];
+ *   int usbDescriptorStringVendor[];
+ *   int usbDescriptorStringDevice[];
+ *   int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE   (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ *   USB_CFG_DESCR_PROPS_DEVICE
+ *   USB_CFG_DESCR_PROPS_CONFIGURATION
+ *   USB_CFG_DESCR_PROPS_STRINGS
+ *   USB_CFG_DESCR_PROPS_STRING_0
+ *   USB_CFG_DESCR_PROPS_STRING_VENDOR
+ *   USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ *   USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ *   USB_CFG_DESCR_PROPS_HID
+ *   USB_CFG_DESCR_PROPS_HID_REPORT
+ *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE                  0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION           0
+#define USB_CFG_DESCR_PROPS_STRINGS                 0
+#define USB_CFG_DESCR_PROPS_STRING_0                0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR           0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT          0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    0
+#define USB_CFG_DESCR_PROPS_HID                     0
+#define USB_CFG_DESCR_PROPS_HID_REPORT              0
+#define USB_CFG_DESCR_PROPS_UNKNOWN                 0
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+/* #define USB_INTR_CFG            MCUCR */
+/* #define USB_INTR_CFG_SET        ((1 << ISC00) | (1 << ISC01)) */
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         GIMSK */
+/* #define USB_INTR_ENABLE_BIT     INT0 */
+/* #define USB_INTR_PENDING        GIFR */
+/* #define USB_INTR_PENDING_BIT    INTF0 */
+
+#endif /* __usbconfig_h_included__ */